max device voltage max device current max device dissipated power rf input power storage temperature junction temperature operating temperature thermal resistance esd (hbm) +6.0 v 130 ma 0.63 w +17 dbm -55oc to 150oc 150oc -40oc to +85oc 85o c/w 1000 v absolute maximum ratings operation of this device above any of these parameters may cause permanent damage. dc-6.0 ghz ingap hbt mmic matched gain block amplifier page 1 of 7 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7003-bd features chip layout low operating voltage: 5v 31.5 dbm output ip3 @ 850 mhz 2.9 db noise figure @ 850 mhz 20.7 db gain @ 850 mhz 16.6 dbm p1db @ 850 mhz low performance variation over temperature 100% dc on-wafer testing esd protection on all die: >1000v hbm low thermal resistance: <85oc/watt pa driver amp, if amp, lo buffer amp cellular, pcs, gsm, umts wireless data and satcom transmit and receive functions catv applications typical performance notes: 1. performance in mimix eval board, vs = 5 v, id = 50 ma typ., rbias = 20 , zs = zl = 50 , oip3 tone spacing = 1 mhz, pou t per tone = 3 dbm. 2. values reflect performance in recommended application circuit. 3. only on-wafer dc test is done. devices are not tested for rf performance. 850 mhz 1950 mhz 2400 mhz 3500 mhz units max. typ. min. max. typ. min. max. typ. min. max. typ. min. temperature (oc) parameter small signal gain output p1db output ip3 noise figure operating current input return loss output return loss pout @ -45 dbc, acp is-95, 9 forward channels +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 19.5 19.3 15.6 15.0 30.0 29.0 46 42 14.0 13.0 17 16 20.7 20.7 16.6 16.6 31.5 31.5 2.9 2.9 50 50 20.0 20.0 25 25 10.5 10.5 21.9 22.1 3.7 4.0 54 58 16.8 16.6 14.4 14.0 26.5 26.0 46 42 13.0 12.0 13 12 18.0 18.0 15.4 15.4 28.0 28.0 3.1 3.1 50 50 17.0 17.0 18 18 10.0 10.0 19.2 19.4 3.9 4.2 54 58 15.8 15.6 13.2 12.8 25.3 24.8 46 42 12.0 11.0 14 13 17.0 17.0 14.2 14.2 26.8 26.8 3.2 3.2 50 50 16.0 16.0 19 19 18.2 18.4 4.0 4.3 54 58 15.2 15.2 11.3 11.3 24.1 24.1 3.4 3.4 50 50 15.0 15.0 15 15 db db dbm dbm dbm dbm db db ma ma db db db db dbm dbm description april 2007 - rev 02-apr-07 the cgb7003-bd is a darlington configured, high dynamic range, utility gain block amplifier. designed for applications operating within the dc to 6.0 ghz frequency range, mimix?s broadband, cascadable, gain block amplifiers are ideal solutions for transmit, receive and if applications. these mmic amplifiers are available in bare die form. mimix's ingap hbt technology and an industry low thermal resistance offers a thermally robust and reliable gain block solution. the ingap hbt die have extra pads to enable thorough dc testing. this unique test capability and the inclusion of esd protection on all die, significantly enhances the quality, reliability and ruggedness of these products. with a single bypass capacitor, optional rf choke and two dc blocking capacitors, this gain block amplifier offers significant ease of use in a broad range of applications.
page 2 of 7 typical s-parameter and noise performance dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7003-bd april 2007 - rev 02-apr-07
linearity performance - base station acp ? is-95 p1db vs frequency 6 8 10 12 14 16 18 012 3 456 frequency (ghz) p1db (dbm) 25 c -40 c 85 c oip3 vs frequency 2 3 25 27 29 3 1 33 0 0.5 1 1.5 2 2.5 33 .5 4 frequency (ghz) oip3 (dbm) 25 c -40 c 85 c 1 mhz separation, 3 dbm/tone page 3 of 7 typical power and linearity performance dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7003-bd april 2007 - rev 02-apr-07
page 4 of 7 typical scattering parameters ( v d = +4.07 v , icc = 51.5 ma, t = 2 3 c, device in a 50 ohm system) frequency s 11 s 21 s 12 s 22 (mhz) (mag) (ang) (mag) (ang) (mag) (ang) (mag) (ang) 100 0.027 -170.5 12.72 17 3 .4 0.065 0. 3 0.012 -7 3 .2 200 0.028 -158.2 12.61 166.8 0.066 -0.2 0.02 3 -87. 3 3 00 0.0 3 2 -149.4 12.50 160.4 0.066 0.1 0.0 3 4 -96.8 400 0.0 3 5-14 3 .6 12. 3 5 154.0 0.066 -0.2 0.044 -10 3 .8 500 0.040 -1 3 8.0 12.16 147.8 0.067 -0.1 0.055 -109.9 600 0.045 -1 3 4.7 11.96 141.6 0.068 -0. 3 0.064 -115.8 700 0.051 -1 33 .1 11.74 1 3 5.6 0.069 -0.5 0.07 3 -121.8 800 0.056 -1 3 2.5 11.50 129.6 0.070 -0.8 0.082 -127.0 900 0.062 -1 3 1.4 11.26 12 3 .8 0.071 -1.2 0.090 -1 3 1.9 1000 0.069 -1 3 2.2 11.01 118.1 0.072 -1.7 0.097 -1 3 7.2 1100 0.075 -1 3 2.5 10.75 112.5 0.074 -2.2 0.104 -142.2 1200 0.081 -1 33 .4 10.49 107.0 0.075 -2.9 0.109 -146.9 1 3 00 0.087 -1 3 4.7 10.22 101.6 0.077 - 3 .6 0.114 -151.5 1400 0.09 3 -1 3 6.0 9.95 96. 3 0.078 -4.4 0.119 -155.9 1500 0.099 -1 3 7.4 9.70 91.1 0.080 -5.2 0.12 3 -160.1 1600 0.106 -1 3 9.2 9.45 86.0 0.082 -6.2 0.126 -164.4 1700 0.112 -140.9 9.20 81.0 0.084 -7.2 0.129 -168.2 1800 0.118 -142.6 8.95 76.1 0.085 -8.4 0.1 3 2 -172. 3 1900 0.124 -144.7 8.72 71.4 0.087 -9.5 0.1 33 -176.2 2000 0.129 -146.7 8.50 66.7 0.089 -10.8 0.1 3 5 179.8 2100 0.1 3 5 -149.0 8.28 62.0 0.091 -12.1 0.1 3 6 176.1 2200 0.140 -151.0 8.06 57.4 0.094 -1 3 .5 0.1 3 7 172. 3 2 3 00 0.146 -15 3 .5 7.86 52.9 0.096 -15.0 0.1 3 8 168.7 2400 0.151 -156.0 7.66 48.4 0.098 -16.5 0.1 3 9 164.9 2500 0.155 -158.5 7.48 44.0 0.100 -18.1 0.1 3 9 161.2 2600 0.159 -161.2 7.29 3 9.7 0.102 -19.7 0.1 3 9 157.4 2700 0.16 3 -16 3 .8 7.12 3 5.4 0.104 -21.4 0.1 3 915 3 .5 2800 0.167 -166.5 6.96 3 1.2 0.107 -2 3 .1 0.140 149.9 2900 0.171 -169.5 6.80 27.0 0.109 -24.9 0.141 146.2 3 000 0.174 -172. 3 6.65 22.8 0.111 -26.7 0.141 142.5 3 100 0.178 -175.2 6.51 18.7 0.114 -28.5 0.142 1 3 8.9 3 200 0.181 -178.2 6. 3 7 14.6 0.116 - 3 0.5 0.14 3 1 3 5.0 33 00 0.185 178.4 6.24 10.5 0.119 - 3 2.5 0.144 1 3 1. 3 3 400 0.189 175.1 6.12 6.4 0.121 - 3 4.5 0.145 127.4 3 500 0.192 171.8 6.00 2.4 0.124 - 3 6.6 0.147 12 3 .6 3 600 0.195 168.4 5.88 -1.7 0.126 - 3 8.7 0.148 119.8 3 700 0.198 164.7 5.77 -5.7 0.128 -40.8 0.150 115.8 3 800 0.201 161.0 5.66 -9.7 0.1 3 1-4 3 .0 0.15 3 111.7 3 900 0.204 156.9 5.56 -1 3 .7 0.1 3 4 -45.2 0.156 107.7 4000 0.206 152.8 5.46 -17.7 0.1 3 6 -47.4 0.159 10 3 .4 4100 0.209 148.6 5. 3 7 -21.7 0.1 3 8 -49.8 0.16 3 99.1 4200 0.210 144. 3 5.27 -25.6 0.141 -52.1 0.168 94.9 4 3 00 0.211 1 3 9.5 5.18 -29.6 0.144 -54.5 0.17 3 90.5 4400 0.21 3 1 3 4.6 5.10 - 33 .6 0.146 -56.9 0.179 86.0 4500 0.215 129.5 5.01 - 3 7.6 0.148 -59. 3 0.185 81. 3 4600 0.216 124.6 4.9 3 -41.5 0.151 -61.8 0.192 77.0 4700 0.217 119.5 4.85 -45.5 0.15 3 -64. 3 0.200 72.8 4800 0.218 114.0 4.78 -49.5 0.156 -66.9 0.208 68.5 4900 0.221 108.1 4.70 -5 3 .5 0.158 -69.5 0.218 64.1 5000 0.224 102.1 4.6 3 -57.6 0.160 -72.2 0.229 59.7 continues n ext page. s-parameter data files are available online at: www.mimixbroadband.com dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7003-bd april 2007 - rev 02-apr-07
page 5 of 7 typical scattering parameters ( v d = +4.07 v , icc = 51.5 ma, t = 2 3 c, device in a 50 ohm system) frequency s 11 s 21 s 12 s 22 (mhz) (mag) (ang) (mag) (ang) (mag) (ang) (mag) (ang) 5100 0.227 96.4 4.55 -61.6 0.16 3 -74.8 0.2 3 9 55.4 5200 0.229 90.7 4.48 -65.6 0.165 -77.5 0.249 51. 3 5 3 00 0.2 3 2 84.7 4.42 -69.6 0.167 -80. 3 0.260 47.2 5400 0.2 3 7 78.2 4. 3 5-7 3 .7 0.169 -8 3 .1 0.27 3 42.8 5500 0.24 3 71.7 4.27 -77.8 0.171 -85.9 0.286 3 8.5 5600 0.249 65.5 4.21 -81.8 0.17 3 -88.7 0.299 3 4.4 5700 0.255 59.4 4.14 -85.9 0.175 -91.7 0. 3 1 33 0.5 5800 0.262 5 3 .2 4.07 -90.1 0.177 -94.6 0. 3 27 26.2 5900 0.269 46.5 4.00 -94. 3 0.178 -97.6 0. 3 4 3 22.0 6000 0.279 40.0 3 .9 3 -98.4 0.179 -100.6 0. 3 59 17.9 6100 0.290 33 .9 3 .86 -102.5 0.181 -10 3 .6 0. 3 76 1 3 .8 6200 0. 3 00 27.9 3 .79 -106.7 0.182 -106.6 0. 3 9 3 9.9 6 3 00 0. 3 10 21.9 3 .72 -110.9 0.18 3 -109.7 0.409 6.0 6400 0. 3 21 15.7 3 .64 -115.0 0.18 3 -112.8 0.426 2.1 6500 0. 333 9.7 3 .57 -119.2 0.184 -115.9 0.444 -1.8 6600 0. 3 47 4.1 3 .49 -12 3 .4 0.184 -118.9 0.462 -5.6 6700 0. 3 60 -1.1 3 .42 -127.5 0.184 -122.0 0.478 -9. 3 6800 0. 3 72 -6.4 3 . 3 4-1 3 1.7 0.184 -125.1 0.496 -12.9 6900 0. 3 84 -11.7 3 .27 -1 3 5.8 0.184 -128. 3 0.512 -16.5 7000 0. 3 97 -17.1 3 .19 -1 3 9.9 0.184 -1 3 1.4 0.5 3 0 -20.2 7100 0.411 -22.2 3 .11 -144.0 0.18 3 -1 3 4.5 0.546 -2 3 .7 7200 0.425 -27.0 3 .0 3 -148.1 0.182 -1 3 7.5 0.562 -27.4 7 3 00 0.4 3 7- 3 1.6 2.95 -152.1 0.181 -140.6 0.576 - 3 0.8 7400 0.448 - 3 6. 3 2.88 -156.2 0.180 -14 3 .6 0.591 - 3 4.2 7500 0.460 -41.1 2.80 -160.2 0.179 -146.7 0.605 - 3 7.7 7600 0.47 3 -45.7 2.72 -164.1 0.177 -149.8 0.620 -41.1 7700 0.486 -50.0 2.64 -168.1 0.175 -152.7 0.6 3 4 -44.5 7800 0.497 -54.0 2.57 -171.9 0.174 -155.6 0.646 -47.8 7900 0.506 -58.0 2.49 -175.7 0.172 -158.4 0.658 -50.9 8000 0.515 -62.2 2.42 -179.5 0.170 -161.2 0.670 -54.0 8100 0.526 -66. 3 2. 3 5 176.7 0.168 -164.1 0.681 -57.1 8200 0.5 3 7 -70.2 2.27 17 3 .0 0.166 -167.0 0.69 3 -60.2 8 3 00 0.546 -7 3 .6 2.20 169.4 0.164 -169.6 0.70 3 -6 3 .1 8400 0.55 3 -77.0 2.14 165.9 0.161 -172.2 0.712 -65.9 8500 0.559 -80.5 2.08 162.4 0.159 -174.9 0.720 -68.7 8600 0.565 -84.2 2.01 158.8 0.157 -177.6 0.728 -71.4 8700 0.57 3 -87.7 1.95 155. 3 0.155 179.8 0.7 3 6 -74.2 8800 0.579 -90.8 1.89 152.0 0.152 177.4 0.74 3 -76.8 8900 0.58 3 -9 3 .7 1.8 3 148.6 0.150 175.1 0.749 -79. 3 9000 0.585 -96.8 1.78 145. 3 0.149 172.6 0.755 -81.7 9100 0.587 -100.1 1.72 142.0 0.147 170.1 0.759 -84.2 9200 0.591 -10 3 .4 1.67 1 3 8.6 0.144 167.6 0.765 -86.6 9 3 00 0.595 -106.4 1.62 1 3 5.4 0.142 165. 3 0.770 -89.0 9400 0.597 -109.0 1.57 1 3 2.2 0.140 162.9 0.775 -91.4 9500 0.598 -111.8 1.5 3 129.1 0.1 3 8 160.7 0.778 -9 3 .6 9600 0.597 -114.8 1.48 125.9 0.1 3 6 158.4 0.781 -95.8 9700 0.597 -117.8 1.44 122.7 0.1 3 4 156.0 0.784 -98.1 9800 0.600 -120.6 1. 3 9 119.6 0.1 3 115 3 .7 0.788 -100. 3 9900 0.601 -12 3 .1 1. 3 5 116.6 0.129 151.6 0.791 -102.4 10000 0.601 -125.4 1. 3 111 3 .7 0.127 149.5 0.794 -104.5 s-parameter data files are available online at: www.mimixbroadband.com dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7003-bd april 2007 - rev 02-apr-07
page 6 of 7 application circuit recommended bias resistor values for id = 35 ma supply voltage (vs) 5v 6v 7v 8v 10v 12v rbias (1/8w) 20 39 59 ???? rbias (1/4w) ?? ?? rbias (1/2w) ? ? ? ? 120 160 note: rbias provides dc bias stability over temperature. 2 rf in vs rf out c1 c2 note: this schematic represents the topology of the application circuit recommended by mimix. uuuu l1 r bias = (vs - vd) / id 4 3 1 vd r1 c3 78 dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7003-bd april 2007 - rev 02-apr-07 ref designator value c1, c2 1000 pf c3 1.0 f l1 56 nh d i / ) d v - s v ( = s a i b r 1 r physical dimensions bonding configuration
page 7 of 7 dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7003-bd april 2007 - rev 02-apr-07 handling and assembly information caution! - mimix broadband mmic products contain gallium arsenide (gaas) which can be hazardous to the human body and the environment. for safety, observe the following procedures: do not ingest. do not alter the form of this product into a gas , powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. observe government laws and company regulations when discarding this product. this product must be discarded in accordance with methods specified by applicable hazardous waste procedures. life support policy - mimix broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the president and general counsel of mimix broadband. as used herein: (1) life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) a critical component is any compone nt of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. esd - gallium arsenide (gaas) devices are susceptible to electrostatic and mechanical damage. die are supplied in antistatic containers, which should be opened in cleanroom conditions at an appropriately grounded anti-static workstation. devices need careful handling using correctly designed collets, vacuum pickups or, with care, sharp tweezers. die attachment - gaas products from mimix broadband are 0.100 mm (0.004") thick. microstrip substrates should be brought as close to the die as possible. the mounting surface should be clean and flat. if using conductive epoxy, recommended epoxies are tanaka ts3332ld, die mat dm6030hk or dm6030hk-pt cured in a nitrogen atmosphere per manufacturer's cure schedule. apply epoxy sparingly to avoid getting any on to the top surface of the die. an epoxy fillet should be visible around the total die periphery. for additional information please see the mimix "epoxy specifications for bare die" application note. wire bonding - windows in the surface passivation above the bond pads are provided to allow wire bonding to the die's gold bond pads. the recommended wire bonding procedure uses gold 0.025 mm (0.001") diameter ball bonds. aluminum wire should be avoided. thermo-compression bonding is recommended though thermosonic bonding may be used providing the ultrasonic content of the bond is minimized. bond force, time and ultrasonics are all critical parameters. bonds should be made from the bond pads on the die to the package or substrate. all bonds should be as short as possible. part number for ordering description CGB7003-BD-000V rohs compliant die packed in vacuum release gel paks
|
